Order fill rate calculator

Measure how much of what customers ordered you actually shipped, at three levels: whole orders, order lines and units. Use it to find out whether short shipments come from a few big gaps or many small ones.

Calculate your fill rates

Use the same period for all three pairs. An order or line counts as complete only if it shipped in full the first time.

Result
Order fill rate
94.0%
Line fill rate
98.0%
Unit fill rate
98.5%

Calculated in your browser. Nothing you enter is sent or stored.

Track the stock behind your plan.

Keep warehouse quantities, locations and movements in one workspace. Explore sample stock in the demo or start with your own items for free.

Free during open beta. No card. No sales call.

The formula

Order fill rate = orders shipped complete ÷ orders shipped × 100; line fill rate = lines shipped complete ÷ order lines shipped × 100; unit fill rate = units shipped ÷ units ordered × 100

Orders shipped
Orders that left the building in the period, whether complete or short. Leave out orders still open, and decide once whether cancelled orders count.
Orders shipped complete
Orders where every line shipped in full on the first shipment. An order completed later by a second shipment or a backorder does not count here.
Order lines shipped
The total number of lines on the orders shipped. One line is one SKU on one order, whatever its quantity.
Lines shipped complete
Lines where the full ordered quantity shipped. A line of 12 that shipped 11 is not complete.
Units ordered
Total units the customers asked for on those orders, in base units. Convert cases to units first so every line is counted the same way.
Units shipped
Total units that actually shipped against those orders, in the same base units as units ordered.

Worked example

Say a distributor shipped 480 orders last month, and 452 of them went out complete. Those orders held 1,350 lines, and 1,302 lines shipped in full. Customers ordered 4,200 units and received 4,116. Order fill rate is 452 ÷ 480 × 100 = 94.2%. Line fill rate is 1,302 ÷ 1,350 × 100 = 96.4%. Unit fill rate is 4,116 ÷ 4,200 × 100 = 98.0%. Nearly every unit shipped, yet about one order in seventeen arrived short.

Order, line and unit fill rate: what each tells you

The three rates usually fall in the same order: unit fill rate is highest, line fill rate is lower and order fill rate is lowest. One short line spoils a whole order, so the more lines per order, the wider the gap between them.

Unit fill rate tells you how much demand you served. Line fill rate points at SKUs: a low line rate usually means a handful of items keep running out. Order fill rate is what the customer feels, and it is the closest of the three to on-time in-full scoring, which B2B buyers often use to rate suppliers. Report all three together; any one alone hides something.

Finding the cause of a low fill rate

A fill rate is a symptom. To act on it, sort the short lines by reason. Most fall into a few groups.

  • Nothing to ship: the SKU was out of stock or its stock was on hold, so the line became a backorder.
  • Stock existed but was not found: the system showed units in a bin that the picker found empty. That is an inventory accuracy problem, not a purchasing one.
  • Allocation rules held it back: stock was in another warehouse, reserved for another order or too close to expiry for the customer.
  • Pack multiples: the customer ordered 10 but the SKU sells in cases of 12, so the line was cut or rounded.

Common fill rate calculation mistakes

The formula is simple; the definitions are where numbers go wrong. Decide how you count split shipments and stick to it. If an order that shipped in two parts counts as complete, your order fill rate will look better than what customers experienced.

Keep substitutions and cancellations consistent too. A line the customer agreed to cancel is not the same as a line you could not fill, but many reports treat them alike. Finally, compare periods of the same length and mix. A month with a big promotion will pull every rate down, and that is information, not noise.

Tracking fill rate in a WMS

Fill rate needs a record of what was ordered, what was allocated and what shipped, line by line. In a spreadsheet those three numbers drift apart. In a warehouse system they come from the same order.

In NextStock, allocation records which lines went to backorder, and held or quarantined stock carries its own status, so you can see why a line was short. Fill rate, measured as allocated against ordered, is one of the KPI reports, alongside on-time ship and order cycle time, and it can be delivered on a schedule. When a line is short, you can split the remaining demand and ship it later without losing the original order.

Frequently asked questions

Short, direct answers to the questions warehouse teams ask most.

What is a good order fill rate?

There is no single target. It depends on how many lines your orders carry, what your customers accept and what your contracts say. Track the trend and the reasons for short lines, and set a target with your customers rather than borrowing one.

Is fill rate the same as OTIF?

No. Fill rate measures completeness only. On-time in-full also requires the order to arrive on the agreed date, so an order can be complete but late and still fail OTIF.

Should backorders count against fill rate?

Yes, for the first shipment. The measure asks whether you shipped what was ordered when it was ordered. Shipping the rest later is good service recovery, but it does not change the fact that the first shipment was short.

Why is my unit fill rate high but my order fill rate low?

Because a single short unit makes the whole order incomplete. If orders carry many lines, a few missing units spread across many orders will pull order fill rate down while unit fill rate barely moves. Look at which SKUs cause the short lines.

Your next warehouse move starts here.

Create your own workspace for free, or explore a stocked demo without an account.

Start freeTry the live demo — no signupFree during open beta. No card needed.